MYERS triple shaft (tri-shaft) disperser vacuum mixer. Has disperser blade, auger blade and scrapper blades. Model# V550/500EH-60-40-100/50-1419. Comes with (2) 600 gallon, stainless steel, jacketed tank and (2) carbon steel tanks. Also has emptying system which consists of follower plate and Graco type pump. Parts for the hot oil system including the electrically heated reservoirs, a 460 volt control panel,
a holding tank and a mounting frame (hot oil heater not available). Quoted AIWI
Used Ross VMC-2 Triple Shaft (tri-shaft) Versamixer Mixer. 316 Stainless Steel construction. Vacuum capable. 2 gallon jacketed Vacuum capable mixing can with provision for thermal couple probe (Type J). 50 PSI jacket. Sanitary 80 grit finish. Explosion proof drives and controls. Anchor agitator driven by 1HP, 230/460 volt xp motor (2) high speed dispersers each driven by 1 HP, 230/460 volt motor. Air over bowl lift/lower mechanism. Lift System: 80-100psig/ 4-5 scfm. Electrical 115V/60Hz. Serial# 104930
ROSS Model PVM-2, 2 gallon triple shaft (tri-shaft) vacuum mixer. Mixers include Anchor, Disperser and Emulsifier. Each mixer controlled by VFD. Disperser and Emulsifier driven by 3/4 HP, 3450 RPM, 208-230/460 V motors. Has jacketed vacuum rated 316 Stainless Steel can.
Paul O Abbe Inc. Jacketed and Vacuum rated Sigma Blade / Double Arm Mixer. Approx. 6 Gallon total and 2.5 gallon working capacity. Stainless mixing chamber, lid and blades. Mixing chamber is 15" left to right X 9" front to back x 12" Deep. Driven by 3 HP, 1760, 208-230/460 volt, 3 phase motor into Delroyd gearbox 40:1 ration. Unit equipped with Tilt discharge. Includes (2) Emerson Commander SK Controllers, one each for main drive and tilt drive.
150 Gal JH Day Double Arm/Sigma Blade Mixer. Stainless steel construction, overlapping sigma blades, jacketed bowl, vacuum cover, 60 hp 230/460 volt XP motor, screw tilting bowl with 3 hp motor drive, with vapor recovery system with heat exchanger and receiver pot. Last used in medical Silicone.
Used 35 cuft (1 m3) Krauss Maffei Titus Nauta mixer/conical vacuum blender and dryer, conical dryer. Model TMT1/200. 316 Ti Stainless steel vessel with 316L stainless steel screw. Rated -14.5 PSI/ 40 PSI @ 330 degF (-1/3 bar g @ 165 degC). Jacket and Screw rated 90 PSI @ 330 degF (6 bar @ 165 degC). Screw is 8" dia (200mm). Variable speed, rotational speed of screw blending/drying is 9.7 to 97 RPM. Discharging downward 9.7 to 18 RPM, discharging upward 9.7 to 27 RPM. Jacket capacity is 45 gallon (170 L), screw capacity is 3 gallon (12 L). Main drive is 15 HP, 460 V UL Class 1/2 group C/D. Discharge conveyor is 3 HP, 230/460 V.
used 76 Cu.Ft. (2,150 L/560 gal) JH Day Stainless Steel, Full Vacuum Rated Nauta Mixer system/Conical mixer. Model MK 2 FB-76. 304 Stainless Steel. Has 20 HP, 230/460 volt, 1800 rpm drive for orbital arm with 3 RPM output and 3 HP, 230/460 volt motor for screw with 120 RPM output. Approx. 12'4" from top of blender to bottom. Includes 5HP Kinney Liquid ring vacuum pump model 75-KF and 15 HP Moyno model 2II065G2 CDR discharge pump.
2400 Liter working capacity Fryma model VME 2400 vacuum mixer (~650 gallon), triple shaft, tri-shaft mixer. Fabrication # M10510. The tank has an overall height is 101" to top of lid including legs. It is 87" to the top with the lid removed. The overall diameter of tank with jacket is 63". The interior dimensions are 61" diameter with 54" straight side height, 11" dome top and 11" dish bottom. Working temperatures are 150 c for the interior and the jacket. The interior has a pressure rating of -1/+1 bar and the jacket has a 2.5 bar rating. There
are two agitator drives, a 7.5 hp motor drives a center 3 prop agitator and a scrape agitator through a chain drive and a 50 hp motor drives a disperser type agitator off to the side of the center shaft. The top has an 8" flanged opening that is clamped shut and 6" glass inspection port with light. Top also has a 2" sanitary, 1.5" sanitary, and (2) 1" threaded fitting. The bottom has a 6" sanitary discharge with a pneumatically operated valve. Requires 230/ 460 vac 3 phase electrical supply. Previously used for toothpaste. Good Condition.
500 Gallon Hockmeyer double motion vacuum mixer. Model HCS-11-500 double Concentric two speed Caulking Vacuum Mixer with two 660 gallon non-jacketed mixing cans of 304 stainless steel, an integrated product discharge press, carbon steel platform 20'-0" x 20'-0" and 1/2 ton jib crane with hoist built in 1987. Overall height of machine 263". Mixing cans are 60" ID x 54" overall height. Main motor which runs disperser is 100/50 HP, 1800/900 RPM, 460V, 3/60, X-P. Main reducer CHW200K-L-S with 29.5 to 1 ratio. Scrape agitator is run by 20/10 HP, 45/23 RPM motor. Shaft has 16" diameter disperser blade with scrape agitation blades. Unit is on center post which rotates the lid and agitator assembly. Unit includes vacuum pump and hydraulic pump. Last used to manufacture siliconized acrylic sealant (caulk).