MYERS triple shaft (tri-shaft) disperser vacuum mixer. Has disperser blade, auger blade and scrapper blades. Model# V550/500EH-60-40-100/50-1419. Comes with (2) 600 gallon, stainless steel, jacketed tank and (2) carbon steel tanks. Also has emptying system which consists of follower plate and Graco type pump. Parts for the hot oil system including the electrically heated reservoirs, a 460 volt control panel,
a holding tank and a mounting frame (hot oil heater not available). Quoted AIWI
Myers Engineering Cowels Disperser/Mixer Model # 775A-7.5-2825. 1.5" dia. x 49" Stainless Steel Shaft. Air over oil lift. Motor is 7.5 HP, XP, 3 ph, 3600 rpm, 208/230/460 volts. Has (5) Blades 1-9"; 2-7"; 1-5" and 1-4".
30 HP HOCKMEYER model HVR.25 Disperser. Motor is 30 HP, 200/230/460 volt, 1770 RPM, XP vari-speed motor. Has Stainless Steel. 42" lgth. x 2" dia. shaft with 8" Dia. blade. Has approx. 100 Gallon 26" dia. x 45" T/T, Jacketed, 304 Stainless Steel tank with open top and dish bottom. Mounted on stand with air/oil lift.
Used Ross VMC-2 Triple Shaft (tri-shaft) Versamixer Mixer. 316 Stainless Steel construction. Vacuum capable. 2 gallon jacketed Vacuum capable mixing can with provision for thermal couple probe (Type J). 50 PSI jacket. Sanitary 80 grit finish. Explosion proof drives and controls. Anchor agitator driven by 1HP, 230/460 volt xp motor (2) high speed dispersers each driven by 1 HP, 230/460 volt motor. Air over bowl lift/lower mechanism. Lift System: 80-100psig/ 4-5 scfm. Electrical 115V/60Hz. Serial# 104930
ROSS Model PVM-2, 2 gallon triple shaft (tri-shaft) vacuum mixer. Mixers include Anchor, Disperser and Emulsifier. Each mixer controlled by VFD. Disperser and Emulsifier driven by 3/4 HP, 3450 RPM, 208-230/460 V motors. Has jacketed vacuum rated 316 Stainless Steel can.
used Cowles Dissolver model 7-VTV. Has 36" Stainless Steel Shaft. 7.5 HP, 230/460 volt. Has Baldor Vari-Speed Controller. Air over oil lift. Great for mixing 55 gallon drums. 55 gallon drum mixer. See our stainless steel drums for sale http://www.ecrecon.com/category/21/?search=drum
(1) used 10 HP, ROSS Disperser/High Shear Mixer/Homogenizer. 10 HP, 3500 RPM, 230/460 volt, Explosion Proof Motor. Shaft is 3'6" lgth. 73" Overall Height from top of motor to bottom of Shaft, not including lifting eyes.
2400 Liter working capacity Fryma model VME 2400 vacuum mixer (~650 gallon), triple shaft, tri-shaft mixer. Fabrication # M10510. The tank has an overall height is 101" to top of lid including legs. It is 87" to the top with the lid removed. The overall diameter of tank with jacket is 63". The interior dimensions are 61" diameter with 54" straight side height, 11" dome top and 11" dish bottom. Working temperatures are 150 c for the interior and the jacket. The interior has a pressure rating of -1/+1 bar and the jacket has a 2.5 bar rating. There
are two agitator drives, a 7.5 hp motor drives a center 3 prop agitator and a scrape agitator through a chain drive and a 50 hp motor drives a disperser type agitator off to the side of the center shaft. The top has an 8" flanged opening that is clamped shut and 6" glass inspection port with light. Top also has a 2" sanitary, 1.5" sanitary, and (2) 1" threaded fitting. The bottom has a 6" sanitary discharge with a pneumatically operated valve. Requires 230/ 460 vac 3 phase electrical supply. Previously used for toothpaste. Good Condition.
500 Gallon Hockmeyer double motion vacuum mixer. Model HCS-11-500 double Concentric two speed Caulking Vacuum Mixer with two 660 gallon non-jacketed mixing cans of 304 stainless steel, an integrated product discharge press, carbon steel platform 20'-0" x 20'-0" and 1/2 ton jib crane with hoist built in 1987. Overall height of machine 263". Mixing cans are 60" ID x 54" overall height. Main motor which runs disperser is 100/50 HP, 1800/900 RPM, 460V, 3/60, X-P. Main reducer CHW200K-L-S with 29.5 to 1 ratio. Scrape agitator is run by 20/10 HP, 45/23 RPM motor. Shaft has 16" diameter disperser blade with scrape agitation blades. Unit is on center post which rotates the lid and agitator assembly. Unit includes vacuum pump and hydraulic pump. Last used to manufacture siliconized acrylic sealant (caulk).