Blenders / Mixers
Item # BM-340
***SOLD*** Unused 5HP Lightnin Mixer/Agitator Model 82C5. 1750 rpm, 230/460 volt, 84 rpm output. Explosion Proof (XP). Has 10" flange with 12 bolt holes. OD is 16" and Bolt circle is 14.25". Bolt holes are .88". Standard stuffing box packing. Has 316SS Shaft flange, no Shaft.
Item # BM-343
Clamp-on Lightnin Mixer model ND-1, 1/3 HP, 220/440 volt, 1725 RPM into gear reducer. Explosion Proof (XP). 316 Stainless Steel shaft and blades. 44" L x 1/2" dia. shaft with (2) prop type blades that are approx. 9" diameter. Previously mounted on tank that was 3'3" dia. x 3'9" T/T.
Item # BM-287
(2) Each Bridge mounted Hamilton 2 HP Sweep mixer with scraper blades and 2 HP Tree Agitation for 350 gallon Kettle. New motors included.
Item # BM-119
5 HP Agitator drive with 3" diameter x 14'L stainless steel shaft. Rated 38.9:1 ratio, 29 RPMo. Motor is 5 HP, 1160 RPMi, 440 V, explosion proof (XP).
Item # BM-230
1.5 HP Lightnin Agitator model XLO-100D. Motor is 1.5 HP, 1725 RPM, 208-220/440 volt. Shaft is Stainless Steel 2" dia. x 44" Length with 2 sets of turbine props. one is approx. 26" dia. and one is approx. 20". Unit mounted on Stainless Steel bridge that measures 59.25" length x 16" wide with attached baffle. Last used on a 350 Gallon kettle. SOME MAY NOT HAVE BAFFLE. Lightnin Mixer.
Item # BM-208
Agitator, Flange Mount, Mfr. Veenstra B.V. De Holwert 10, Type FRA-150, Holland, Mach # 98.096, 277/480 volt, 1.1 KW (1.5 HP). Stainless Shaft, 36" lgth. x 1.25" dia. with 8" mixing blade.
Item # BM-277
Used clamp-on stainless steel mixer/variable speed agitator with digital readout. Driven by 1/2 HP, 1725 RPM, 115 Volt, single phase motor. Has a 30" lgth. shaft with collapsible agitator blades (approx. 8" in diameter when open) for easy installation inside a port. Sold As Is.
Item # BM-380
***SOLD*** (2) MixMor clamp-on agitator/mixer. Model G-15. UL rated (explosion proof, XP). Stainless steel shaft 1.25" dia x 36" L. Unit 5' OAH. 2 blades on each shaft (one prop type, one disperser type). 1.5/1 HP, 230/460/190/380 V, 1760/1460 RPM, 60/50 Hz. There are (2) mounting stands/lifts available, 7' OAH (sold separately).
Item # BM-432
Used 2 HP Philadelphia Mixer/agitator. Motor is 2 HP, 230/460 V, 1725 RPMi/345 RPMo motor. Bridge mount type. Stainless steel shaft 65"'L (from mounting plate) x 1.25" diameter with (2) sets of agitator blades.
Item # BM-346
used Lightnin model MXC-70V Mixer. 30 HP Explosion Proof (XP) Mixer/Agitator/Disperser. Output RPM 900/450. Motor is 30 HP, 1175 rpm, 460 volt. Has Johnson Speed Controller/Selector. Stainless Steel Shaft is 2.5" dia. x 98" lgth. with prop and 14" dia. Dispersion Blade (Shaft reduces to 2" Dia. near Blades). Approx. 12" Flg. mount (19" OD. , 17" Bolt centers).
Item # BM-347
used 75 HP Philadelphia Gear box for Mixer. Size/Type 3809S. Order # 22220. Input rpm 1750, output 230 rpm. 7.6:1 ratio. S/N 98DID0229-1.
Item # BM-410
used Lab Mixer on stand with variable speed explosion proof (UL, XP) controller. Stand has base for 11.5" diameter (standard 5 gallon bucket). Dayton 1/6 HP, 90 V, 1800 RPM drive motor. Stainless steel agitator shaft 1/2" dia x 12" L with 3" dia blades. Stand mount is 30" H.
Item # BM-433
used 1.5 HP Lightnin Mixer/Agitator Model X6Q150. 208-230/460 volt. Has bracket to mount on angle or remove to mount vertical. No shaft available.
Item # BM-434
used 1 HP Mixer/Agitator with Stainless Steel Shaft. 230/460 volt, 1725 RPM. Bridge mount (4' L x 1' W) or remove and mount on flange. Stainless Steel Shaft is 3/4" diameter x 4'L with (2) prop type blades approx 11" diameter.
Item # BM-436
used Stainless Steel agitator shaft with impeller. 4-blade pitched turbine type. 2" diameter x 5'6" L with 20" diameter impeller.
2" dia x 5'6" L
Item # BM-242
(2) EACH, 600 Gallon LEE 316L Stainless Reactor / Kettle with 1/2 Pipe jacket and High Speed Greerco Disperser. Polished internal Rated 15/FV @ 100 Deg.F. Internal and 100 PSI @ 338 Deg.F on Jacket. Has Greerco model 4HRFM 96, 15 HP, 230/460 volt, 3525 RPM Disperser. 2.5" center bottom outlet reducing to 2" actuated ball valve.
Item # BM-392
***SOLD*** used Hockmeyer drum mixer/immersion mill/basket mill, Model# 09HCP/DM1/4470. Driven by 10 HP, 1755 RPM, 230/460 Volt XP explosion proof motor. Comes with 7 gallon stainless steel jacketed can, 12" dia x 16" H. Jacket rated 14.7 PSIG. High Shear Mixer. Previously used in sanitary process. 9'9" Overall Height.
Item # BM-283
30 HP HOCKMEYER model HVR.25 Disperser. Motor is 30 HP, 200/230/460 volt, 1770 RPM, XP vari-speed motor. Has Stainless Steel. 42" lgth. x 2" dia. shaft with 8" Dia. blade. Has approx. 100 Gallon 26" dia. x 45" T/T, Jacketed, 304 Stainless Steel tank with open top and dish bottom. Mounted on stand with air/oil lift.
Item # BM-291
Used 120 Liter (Approx 30 Gal) Ystral Triple Motion Jacketed Mixing vessel, Model X-3/D. Flat top, dished bottom, leg mounted vessel with casters. 21" dia x 27" Straight side (OAH - 74"). Jacket rated 6 Bar (90 PSI) @ 50 deg C. (2) Disper-mixers 5.5 KW (7.5 HP) & 3.6 KW (5 HP), Side Scraper .37 KW (1/2 HP). Hydraulic Lifting device, Controls. Built 1998, S/N: 15983. (Made in Germany) Tri-shaft.
Item # BM-355
Used Approx. 25 gallon capacity Myers Double Motion change can mixer model 550A-5-5-1475. Stainless steel contacts. Can is stainless steel and approximately 20" diameter X 20" deep, open top with dished bottom and center bottom outlet, on castors. 3 Wing anchor agitator, 5 hp 3 phase 60 cycle 230/460 volt 1740 rpm. High speed prop agitator, 5 hp 3 phase 60 cycle 230/460 volt. Hydraulic lift. Built 2001.
Item # BM-312
used Cowles Dissolver model 7-VTV. Has 36" Stainless Steel Shaft. 7.5 HP, 230/460 volt. Has Baldor Vari-Speed Controller. Air over oil lift. Great for mixing 55 gallon drums. 55 gallon drum mixer. See our stainless steel drums for sale http://www.ecrecon.com/category/21/?search=drum
Item # BM-409
***SOLD*** Used Hockmeyer Disperser, Model HV15. 1-3/4" Diameter x 41" long 304 stainless steel shaft with a 5-1/2'' diameter blade. Will center in an approximate 40" diameter can. 360 degree rotation, 53-1/2" rise, air/oil lift, tank holder. Hand operated variable speed pulley drive, speed range approximately 650-3200 rpm. Unit driven by a 15 hp, 3/60/230/460 volt, 1760 rpm XP motor. Base mounted
Item # BM-421
ARDE-BARINCO High Shear Reversible Homogenizer/Disperser/Emulsifier for high shear batch processing. Top mounted mixer. Driven by 7.5 HP, 230/460 Volt, 3465 RPM, Explosion Proof (XP) Motor. Shaft is 33" Lgth. Unit is 5'4" OAH.
Item # BM-329
***SOLD*** 150 Gal JH Day Double Arm/Sigma Blade Mixer. Stainless steel construction, overlapping sigma blades, jacketed bowl, vacuum cover, 60 hp 230/460 volt XP motor, screw tilting bowl with 3 hp motor drive. Includes vapor recovery system with heat exchanger and receiver pot. Last used in medical Silicone. High viscosity mixer. Approx. 3' back to front x 3'3" wide x 3' deep. Approx. 210 gallons total volume.
DOUBLE ARM / SIGMA BLADE
Item # BM-381
***SOLD*** 2 Gallon Paul Abbe Jacketed Double Arm/Sigma Blade Mixer. Model SBM1. Stainless steel construction. Mixing chamber is 7"x 9.5" wide x 9" deep. Approx 2 Gallon (.25 Cu.Ft.) Rated Full Vacuum internal and jacket rated 14.7 PSI @ 250 Deg.F. Motor is Explosion Proof (XP) 2/5 HP, 230/460 volt, 1750 rpm into gear reducer. Last used in sanitary pharmaceutical application.
DOUBLE ARM / SIGMA BLADE
PAUL O ABBE
used Jaygo Jacketed Double Arm/Sigma Blade Mixer/Blender, Model M57. 350 liters (92 Gallon) for sale
Item # BM-425
used Jaygo Jacketed Double Arm/Sigma Blade Mixer/Blender, Model M57. 350 liters (92 Gallon) working capacity (top of blades in vertical position). 500 liters total capacity (top flange). S/N 107016. Requires a 20 to 45 HP Drive. Built 2008. Last used in sanitary plant.
DOUBLE ARM / SIGMA BLADE
Item # BM-81
70 Cu.Ft. Pfaudler Double Cone jacketed blender/dryer. Driven by 10 HP motor into Reeves Varidrive. Rated 20 PSI @ 350 internal, 45 PSI @ 350 jacket. Quotes As is where is.
Item # BM-147
(2) Each: used 30 cu.ft. Gemco Double Cone blenders. Stainless Steel. Rated 125 lbs/cu.ft.. 13.4 RPM blend speed. 4" rotary airlock valve discharge. 5 HP, 1730 RPM, 230/460 V, Positioner motor is 2 HP, 1730 RPM into gear 10:1 ratio. With control panel. Operating height without extensions is 151.75". Extensions add ~31".
Item # BM-395
Used Gemco Model LB-85687 Double Cone Blender/Mixer. 16 Quart, approx. .5 CU.FT. Stainless steel. Shell is 14" Dia. x 9" from center line to outlet. 3" Outlet. Unit equipped with Intensifier bar. Missing discharge cover. Laboratory blender, pilot scale blender.
Item # BM-399
***SOLD*** used Gemco Bench top Slant Cone/Double Cone Blender 16 Qt., 0.5 Cubic Foot. 115 Volt. S/N LB-90980. Rated 125#/cu.ft.. Shell is approx. 14" diameter x 9" from center line to outlet. 3" Outlet. Laboratory blender, pilot scale blender.
Item # BM-404
***SOLD***Paul O Abbe model 24 RCB Portable 2.4cu.ft. Double Cone, Rotary Conical Blender with 1HP, 208-230/460, 3PH, 60 Hz Baldor Electric Motor. 4" valve outlet. S/N-A42112. Overall dimensions 69" wide x 29" deep x 7' OAH. Last used in sanitary pharmaceutical application
PAUL O. ABBE
Item # BM-384
***SOLD*** unused OAKES Model 4MBH31A High Shear, Bearing Housing Mixer. Hastelloy Contact parts. 1/2" Inlet/Outlet. Includes AB Powerflex inverter. According to the Mfr. "The Bearing Housing Mixer is ideally suited for highly viscous slurry applications, or when your usage requires only the mixing head and drive assembly. The unique design of the high shear Oakes Rotor/Stator Mixing Head is the key to consistent final densities. Aerate and/or homogenize slurry with minimal heat rise." Applications include: biscuit marshmallow, cake batter, candy marshmallow, cheese cake, icing, layer cake, nougat, pie fillings, soy bean, whipped butter and more.
Item # BM-298
Oakes Model 14 Continuous, inline Mixer. Has high shear rotor/stator mixing head. Driven by 15 HP, 1760 rpm, 230/460 volt motor into gear box. 1.5" Sanitary tri-clamp inlet, 2" outlet. Oakes mixers are designed to homogenize or aerate slurry to produce a highly uniform and stable cell structure. Last used in Sanitary application in food plant. Stamped on mixer B14-1317 and F14-1304.
Item # BM-233
Used ROSS 100 Gallon model RVMS-100, Pharmaceutical mixing reactor. Mixing vessel Rated 30 PSI @ 300 Deg.F. Has "Egg Beater" and turbine blade on one mixing shaft. Mixer drive is Lightnin 1.74 HP, 208-220/440 volt, 1725/1425 RPM. Has lift to raise mixer and lid.
Item # BM-279
***SOLD*** 10 HP, ROSS Disperser/High Shear Mixer/Homogenizer. 10 HP, 3500 RPM, 230/460 volt, Explosion Proof Motor. Shaft is 3'6" lgth. 73" Overall Height from top of motor to bottom of Shaft, not including lifting eyes. 4" Dia. mixing head. Homogenizing Mixer.
Item # BM-293
Quadro Y-Tron Model Z5 Multi-row toothed rotor-stator mixer/mill. (3) Stage unit. S/N Z5-0103. Rated up to 300 GPM. Stator gap size in 0.5mm. Driven by 40 HP, 230/460 volt, 1775 rpm, WEG inverter duty/severe duty motor. Mechanical Seal. Designed for inline, high-shear process applications such as immiscible phase emulsifying/homogenizing, wet grinding, deagglomeration and fine solids dispersing. Sanitary construction. Built in 2013. Appears to be Unused. Includes spare seal kit and bearings ($3500). Cost for new unit approx. $60,000. Quadro Ytron.
Item # BM-386
USED GEA AEROMATIC FIELDER Model PMA-1 High Shear Mixer/Granulator with MiniPpurge system. Rotor 1 RPM 55-556. Rotor 2 RPM 1500-3000. Only Rotor 1 installed. Bowl is 10" dia. x 8" Ht. S/N 06358.1310
GEA AEROMATIC FIELDER
Item # BM-370
***SOLD*** used Microfluidics Lab Microfluidizer Electric-Hydraulic Processor/Homogenizer , Model M140K. Stainless Steel. Unit designed for high shear rates, maximizing the energy per unit fluid volume resulting in uniform submicron partical and droplet sizes. Pressure range 800 to 40,000 PSI (544 to 2720 Bar), flow rate range up to approximately 500 Ml/Min, feed temp range -15 Degrees F to 165 Degrees F (-25 Degrees C to 75 Degrees C), hold up volume 23.1 Ml, sample size 1 Liter to continuous. Designed for inline cleaning. Includes a hydraulic motor, on board heat exchanger and inlet reservoir. Mounted on casters.
Item # BM-374
Quadro Y-Tron Model Z3 Multi-row toothed rotor-stator mixer/mill. S/N Z3-0013. Rated up to 100 GPM. Designed for inline, high-shear process applications such as immiscible phase emulsifying/homogenizing, wet grinding, deagglomeration and fine solids dispersing.
Item # BM-418
used Waukesha Cherry Burrell In line Shear Pump/Mixer, Model SP4, used. 316 Stainless Steel. Nominal capacity to 30 gallons per minute at 150 psi at 3600 rpm to 300 degrees F. 2" inlet/outlet. Driven by a 5 HP, 208-230/460 volt, 3450 rpm motor. Has a Vacon X seris Vari-speed drive. Approximately 4.5" diameter x 2" deep chamber with slotted rotors and stator. Unit does not have inner rotor blade and spacer. Last used in sanitary food plant.
Item # BM-419
used Waukesha Cherry Burrell In line Shear Pump/Mixer, Model SP4, used. 316 Stainless Steel. Nominal capacity to 30 gallons per minute at 150 psi at 3600 rpm to 300 degrees F. 2" inlet/outlet. Driven by a 10 HP, 208-230/460 volt, 3525 rpm motor. Has a Vacon X seris Vari-speed drive. Approximately 4.5" diameter x 2" deep chamber with slotted rotors and stator. Unit does not have inner rotor blade and spacer. Last used in sanitary food plant.
Item # BM-420
used Key International Bench Top High Shear Granulator Mixer Model KG-5. S/N: JI-3728. Comes with 2 choppers & 3 bowls. Last used in Pharmaceutical application.
Item # BM-427
used Arde-Barinco Laboratory High Shear Homogenizer Mixer. 1 Phase, 120 volt, 60 Hz. Mixing head is 2". Stand is 38" Height. Shaft is 16" lgth. SN: 6053. Last used in sanitary plant. Video of unit running available.
Item # BM-428
used Silverson Model 450LS High Shear In-Line mixer/homogenizer. 2" Inlet/outlet. 10 HP, 3450 rpm, 208-230/460 volt motor. Video of unit running available.
Item # BM-429
used Votator Horizontal Mixer, Whipper-Emulsifier. Model CR6. Has 5 HP Motor, 220/460 Volts, with S/S Square D Safety Switch. S/N 72 026V. Design Operating Product Pressure 250 PSI @ 100 Deg.F. Last used in sanitary food plant. Mounted on Portable S/S Frame
Arde Barinco High Shear Reversible Homogenizer/Disperser/Emulsifier for high shear batch processing for sale
Item # BM-435
used Arde Barinco High Shear Reversible Homogenizer/Disperser/Emulsifier for high shear batch processing. Model CJ-20. 24" immersion length shaft with (3) support rods holding 4.5” dia. rotor housing. 3.5" diameter, 3 blade 30 degree axial flow rotor. 7” adjustable baffle plate with (1) control rod and locking handle. All major wetted parts Type 316 stainless steel except Rulon mixing head bearing (FDA accepted). Has 3 HP S/S Clad Motor. With Operating Manual.
Item # BM-372
***SOLD*** used Niro Soavi High Pressure Homogenizer. Model: PANDA. Maximum working pressure: 21755 psi(150 MPa). Standard flow rate: 2.6 gal/hr (10 l/hr). The unit operates at temperatures up to 194 Deg.F. The Panda is a high pressure homogenization unit designed for laboratory and small scale production in the pharmaceutical and biotechnological industries. Tri-clamp inlet/outlet connections. Sanitary designed and easily disassembled for manual cleaning and sterilization in place (SIP). Homogenizer is made with FDA approved product contact materials. Digital pressure gauge.
Item # BM-373
***SOLD*** used Arde Barinco Cavitron Continuous High Shear Homogenizer/Mixer/Reactor System. Model 1025. Rated 4-66 GPM. Has 40 HP, 3540 rpm, 575 volt Explosion Proof Inverter Duty Motor. Unit mounted on Stainless Skid with cooler. Free of rheological restrictions, Cavitron can process solid, liquid, gaseous, fibrous and pasty media. That makes it widely applicable in a variety of industries including Food, Pharmaceutical, Chemical and Cosmetics.
Item # BM-300
200 Gallon BREDDO Model LDTW-200 Jacketed Likwifier/Liquifier/Liquefier on Casters. Driven by 20 HP, 230/460 volt motor. 90 PSI Jacket. Has Watlow electric heater with pump and control. Has AB starters for Thompsen model 69804-04, 1.5 HP, 208-230/460 volt 1755 rpm transfer pump and Liquifier unit. Last used to make Sugar Glaze for Bakery in sanitary application. Overall dimensions approx. 5'10" x 4'4" wide x 6'6" lgth.
Item # BM-389
***SOLD*** used 500 Gallon APV Crepaco Likwifier/ Liquifier/Liquefier. Triple motion. Has (1) top mounted Mixer with scraper/sweep blades agitator and also (1) shaft with (2) sets of pitched blade props (sweep is 7.5 HP, 1735 RPMi/10 RPMo; Shaft with props is 7.5 HP, 1735 RPMi/85 RPMo). Bottom mounted high shear mixer driven by 25 HP, 1170 RPM, 230/460 V. Jacket rated 90 PSI @ 350/-20 Deg.F. 5' dia x 3' T/T (5' from top of dish to bottom of cone). 13'6" Overall Height. Sanitary construction.
Item # BM-417
used 300 Gallon Walker Jacketed Likwifier/ Liquifier/Liquefier with Sweep Mixer. Jacket rated 75 PSI @ 320 Deg.F. 316L Stainless Steel. Has Top mounted 7.5 HP Mixer with scraper/sweep blades agitator on side and bottom mounted Liquifier/chop/dissolver/high shear assembly driven by 40 HP, 230/460 volt, 1775 rpm motor. 32" straight side, dish bottom, 57" dia. Top Manway. Model MM-DS-PZ, s/n 28086. 9'3" OAH. Last used in sanitary food plant.
Item # BM-260
Used 35 cuft (1 m3) Krauss Maffei Titus Nauta mixer/conical vacuum blender and dryer, conical dryer. Model TMT1/200. 316 Ti Stainless steel vessel with 316L stainless steel screw. Rated -14.5 PSI/ 40 PSI @ 330 degF (-1/3 bar g @ 165 degC). Jacket and Screw rated 90 PSI @ 330 degF (6 bar @ 165 degC). Screw is 8" dia (200mm). Variable speed, rotational speed of screw blending/drying is 9.7 to 97 RPM. Discharging downward 9.7 to 18 RPM, discharging upward 9.7 to 27 RPM. Jacket capacity is 45 gallon (170 L), screw capacity is 3 gallon (12 L). Main drive is 15 HP, 460 V UL Class 1/2 group C/D. Discharge conveyor is 3 HP, 230/460 V.
Item # BM-272
used 76 Cu.Ft. (2,150 L/560 gal) JH Day Stainless Steel, Full Vacuum Rated Nauta Mixer system/Conical mixer. Model MK 2 FB-76. 304 Stainless Steel. Has 20 HP, 230/460 volt, 1800 rpm drive for orbital arm with 3 RPM output and 3 HP, 230/460 volt motor for screw with 120 RPM output. Approx. 12'4" from top of blender to bottom. Includes 5HP Kinney Liquid ring vacuum pump model 75-KF and 15 HP Moyno model 2II065G2 CDR discharge pump.
Item # BM-397
used Rietz Bepex Cheese Creamer Paddle Blender Model RC-80. 57"W x 105"L S/S, Approx. 1200 Gallons. S/N 8C-800030, with 6" Diameter Shaft, Interrupted ribbon/paddle design. 10 hp SEW Drive Motor, 1740 rpm, 230/460V 3 Phase, Includes (2) Top Access Doors, Spray Ball, 4" End Bottom Outlet, Mounted on S/S Legs. Last used in sanitary application. Overall Dimensions 154"L x 64" W x 76"H
Item # BM-403
used Continuous Jacketed Paddle Mixer/Blender/Dryer/Conveyor. Trough is 20" wide x 22" deep x 12' Lgth. Trough is jacketed and shaft for paddles can be heated/cooled. Drive is 1.5 HP, 208-230/460 volt, 1725 rpm into gear reducer with 45.91:1 ratio. Discharge is approx. 17" x 7". Unit has ability to incline and be portable on wheels. Stainless Steel Construction. has 3" Drain. Approx. 20 CU.FT. working capacity. Last used in food plant in a sanitary application.
20" x 12'
Item # BM-311
used 53 Cu.Ft. American Process Systems Paddle Blender model FZM-53 (1500 Liter) Twin Shaft Fluidized Zone Mixer/Paddle blender. 304 Stainless Steel. 30 HP 230/460 volt motor. Mixer paddles are 25 RPM. Includes Control Panel. Last used in a sanitary application in food and nutraceutical plant. As per American Process Systems, Fluidized Zone Mixers, provide quick yet gentle blending, short cycles, low operating costs, minimal product degradation and one of the highest production capacities of any other mixer type. Unit can come with Drum Dumper and mezzanine structure for additional cost.
American Process Systems/Eirich
Item # BM-317
***SOLD***270 Cu.Ft. Paddle Blender, Stainless Steel, built by American Process Systems Div of Eirich Machines Model #U270-5998, Equipment Type PB-270 Mixer, 12 ft. Length, SN 5998. 10" outlet with slide gate valve and actuator. Driven by a 30 HP motor into gear box with 13 rpm output. 6" dia. shaft. Air purge seals. Polished interior. Last used in Food Ingredient plant (sanitary application).
American Process Systems/Eirich
Item # BM-356
Used approx. 1 Cu.Ft Marion Type Paddle Mixer, Stainless steel. Equipped with electric blanket heater jacket. 12" wide X 14" long X 16" deep. Safety grate on top. Hinged top cover. 1/2 Hp 3 phase 60 cycle 230/460 volt, 1700 rpm motor with Sew Eurodrive reducer. Center bottom discharge. Mounted with legs.
Item # BM-371
***SOLD*** used 100 Cu.Ft. Scott Paddle Blender. Stainless Steel. Trough dimensions 4' wide X 8' Lgth X 4'6" deep. Driven by a 50 HP, 230/460 volt, 1765 rpm, explosion proof motor into gear reducer. Polished Sanitary Interior. 8" bottom outlet with tri-clamp fitting and valve. ***ON HOLD
SCOTT EQUIPMENT CO
Item # BM-431
used 35 Cu.Ft. Marion Sanitary Stainless Steel Paddle Blender with (2) high speed choppers. Trough has a center bottom outlet (with slide valve), and it is 32" x 72", giving a total capacity of approx 40 cu.ft. The blender has packing glands and outboard roller bearings. The shaft is driven by a 15 HP motor (3/60/230-460V), through a "V" belt drive to a shaft mounted torque arm reducer. The trough has a fixed safety grate. The unit has two choppers. This blender has bolt on legs, putting the outlet 36" off the floor. Appears to be a Marion, no nameplate present.
Item # BM-402
***SOLD*** used 20 Cu.Ft. Marion Paddle Mixer/Blender, Stainless Steel, Sanitary construction. Model SPY-3048-Batch Mixer. Trough is 48" lgth x 39" wide S/N SP-11007. 15 HP, 230/460 volt, 1765 rpm motor into Eurodrive 44.02:1 gearbox. Has ball valve for discharge with actuator. Last used in food plant.
Item # BM-255
***SOLD*** Used Double Planetary Mixer. Believed to be a ROSS CDM-150, 150 gallon. Unit comes with (11) 40" ID x 32" Deep, Carbon Steel Mix Cans with 4" outlets with valve. 15 HP, 1800 rpm, 208-220/440 volt, Explosion Proof motor into Delroyd gear reducer with 89.48:1 ratio (approx. 20 RPM output). It appears to be a CDM-150. **Video of unit running is available.**High viscosity mixer.
Item # BM-331
***SOLD*** used Littleford Model FKM-1200-D Jacketed Plough/Plow Mixer/Dryer. 43 Cu.Ft. total, 26 Cu.Ft. working capacity. Unit equipped with 34 Sq.Ft. Jacketed Dust Collector/Filter. Vessel rated Full Vacuum. Jacket rated 90 PSI @ 330 Deg.F. End plates are also jacketed. Main shaft is hollowed to accommodate heating or cooling media. 304 Stainless Steel. 75 HP, 460 volt motor. Built in 2008 and had little use.
LITTLEFORD DAY INC.
Item # BM-223
65 Cu.Ft. (1840 Liter) working capacity, Jacketed Plow/Plough Mixer with Choppers. Model AG 78 built by Walter Equipment Ltd. (Similar to Littleford FKM-3000). Jacket rated to 15 PSI. Mixing chamber is 115.5" L x 44.5 ID. Main Drive is 60 HP, 460 volt, 1775 RPM into gear box with 155 RPM out (Mixing shaft speed is approx. 100 RPM). Equipped with (4) 10 HP, 208-230/460 volt, 3505 RPM Choppers. Similar size to Littleford FKM-3000
Item # BM-394
used Littleford Model FKM-1200D Batch Type Plow/Plough Mixer, Serial Number: 41626-4181 , 26.1 Cubic Feet Working Capacity (43.4 Total), 316 Stainless Steel. Non-jacketed chamber 32" diameter x 99" straight side, 5" diameter shaft with 8 bolt-on "T" paddles, 2 end scrapers. Driven by a 40hp, 3/60/460 volt, 1725 rpm motor thru a Falk reducer, ratio 11.6 to 1, input/output rpm 1750/155. Openings: top 4", 6", 8", 10". 2 side access doors
Item # BM-412
used Littleford Model FM-300D Jacketed Plough/Plow Mixer with Chopper. 300 Liter (10.6 Cu.Ft.) Has 15 HP, 230/460 Main Drive and 5 HP Chopper motor. Explosion Proof Electrical. Jacket rated 75 PSI @ 320 Deg.F.. Internal rated ATMO @ 320 Deg.F. S/N 41145-3738. Video of unit running available.
Item # BM-378
***SOLD*** used Littleford Plough/Plow Blender, Stainless Steel. Approx. 10 Cu.Ft. (300 Liter) Total Capacity. Mixing chamber is 20" dia. x 58" Lgth. Has 15 HP main Drive and (2) 5 HP Choppers. Non-Jacketed. Unit has side end discharge with slide gate.
Item # BM-301
***SOLD*** used 270 Cu.Ft. Sanitary Stainless Steel Ribbon Blender. Built by American Process Systems. Model U270-5722, Type DRB-270. Approx 12'L X 5'W X 6'D, 75 HP, 208-230/460 volt, 1180 rpm motor into gear reducer, approx. 25 RPM output ribbon. (2) 8" X 8" discharges on bottom ends with air operated gate valves. Mounts for 4 side choppers, 2 on each side. (2) 26" top inlets/man ways with lift out magnetic bars and lids. (1) top 18" X 30" opening with screen. Includes control panel. Last used in a sanitary application in a food plant. Agitated surge blender.
American Process Systems/Eirich
Item # BM-71
50 Cu.Ft. Stainless Steel Double ribbon blender. Stainless ribbon has bolt on teflon wiper. 10" Bottom end outlet. Chain driven. 17 RPM ribbon. 7.5 HP, 1740 RPM, 575 volt, 8.6 amp, motor into gear reducer ratio 20.9:1, 84 rpm output.
Item # BM-72
Stainless Steel 40 cu. Ft. double ribbon blender with a 6" x 92 twin-shaft continuous discharge feeder/ lump breaker/ de-lumper mounted in bottom of trough. Blender is powered by 2 HP motor. Continuous
Item # BM-328
***SOLD*** used 150 Cu.Ft. Stainless Steel Ribbon Blender. Center bottom discharge. Driven by a 50 HP motor. 4'6" W x 9'6" L x 5'2" total depth to bottom of trough. Unit comes with stand. Stand is 8'9" H x 6' x 9'8". Blender overall dimensions: 12'1" L x 5'8" W x 6' H.
Item # BM-382
***SOLD***used 10 Cu.Ft. Stainless Steel Ribbon Blender built by Hayes and Stolz. Model HRSS10-695. Approx. 44" x 22.5" wide x 24" deep. Driven by a 5 HP, 1730 rpm, 230/460 with 24.98 Dodge gear reducer. 6" Bottom outlet with actuated gate valve. overall dimensions 7'5" lgth. x 3'7" wide x 6' ht. Last used in food plant in sanitary application.
HAYES and STOLZ
Item # BM-426
used 120 Cu.Ft. S. HOWES Stainless Steel Ribbon Blender. Driven by 40 HP, 208-230/460 volt motor into Gear reducer. Trough is 144" lgth. x 48" deep x 45" wide. (2) 20HP Bottom Side Entering Choppers/Lumpbreaker Drives with shafts and blades. 14" Center Bottom Discharge with Gemco Discharge valve with actuator. Can come with Premier Pneumatics Receiving Hopper and screw conveyor for additional charge (Item# FC-98). Last used in Food Plant (Bakery).
Item # BM-387
(2) used BlenTech 1200 Gallon (160 Cu.Ft.) Jacketed Mixer/Cooker Kettle. Model BT-600960ZX. BlenTherm units. 316 Stainless Steel. Ribbon/Paddle agitators equipped with scraper blades driven by 30 HP drive rated at 5-30 rpm output speed. Steam Jacket rated 90 PSI @ 331 Deg.F. Last used in sanitary food plant. Can be used for sauces, soups and more.
Item # BM-323
***SOLD*** used 100 CU.FT. ROSS Stainless Steel Ribbon Blender. 120" x 39" x 43" Depth of trough. Has 60 HP, 1770 rpm, 208-230/460 volt motor into dodge gear reducer with 25.66:1 ratio. 8" CBO. Overall dimensions: 183" x 78" x 57".
Item # BM-368
*25% OFF* used 30 Cu.Ft. DAY Ribbon Blender. Stainless steel construction. Trough is 30" wide X 78" lgth X 33" Deep. Has 4" Center bottom outlet. Capacity is approximate. Unit has Motor and chain for drive. Last used in spice blending plant. Can come with top mounted dust collector.
Item # BM-388
used 125 Cu.Ft. Stainless Steel Ribbon Blender. BlenTech Model SM-54084. 316L Stainless Steel. Unit Trough is 84" lgth. X 54" wide. End discharge. Has lid with actuators. Driven by 25 HP motor rated at 30 rpm output. Rated at 127 Cu.Ft. to top of ribbon. Unit has #2 finish. Comes with Fristam FLK250 Rotary lobe discharge pump. Last used in a Sanitary Food Plant.
Item # BM-369
*25% OFF* used 20 Cu.Ft. SCOTT Stainless Steel Ribbon Blender. Trough is 30" wide X 48" lgth X 36" Deep. Has 4" Center bottom outlet. Capacity is approximate. Last used in spice blending plant. Can come with top mounted dust collector.
Item # BM-375
***SOLD*** Used 200 Cu.Ft. Stainless Steel Ribbon Blender. Inside Dimensions: 144" long x 50" wide x 60" deep. 50 HP, 1775, 208-230/460 volt Drive into gear reducer. Unit is approx 18' OAL x 8' OAH x 63" OAW. Last used in Sanitary application in food processing plant.
Item # BM-377
used 87 Cu.Ft. Bepex Ribbon Blenders with Choppers. Stainless steel. Model IMXS-87. Trough is 8'3" lgth. x 3'8" wide x 4' deep. 10" Slide gate valve with actuator on center discharge. Drive is 40 HP, 1770 rpm, 230/460 volt into Dodge gear reducer with 25.6:1 ratio. Unit has (2) 25 HP, 1765 rpm, 230/460 volt Smizers (Choppers/Lumpbreakers). Control panel included. Last used in Sanitary Food Plant.
Item # BM-416
***SOLD*** used 70 Cu.Ft. Jacketed Vacuum Rated Ribbon Blender/Vacuum Dryer, built by Expert Ind. Hastelloy C276. Internal rated Full Vacuum @300 Deg.F. 304SS Jacket rated 70 PSI @ 300 Deg.F. Trough is 95" lgth. x 38" wide x 42" Ht. Has Dome Cover. 12" CBO. Requires a 15 HP Drive(details in drawing).
Item # BM-422
used 7.5 Cu.Ft. Stainless Steel Ribbon Blender. Trough is 20" wide x 48" lgth. x 21.5" deep. Built by LZ Company. Model HB/25. Driven by a 5 HP, 220 Volt, 1745 rpm motor into a 40:1 gear reducer. Control buttons may need to be replaced. Has an approx. 7" center bottom outlet with slide gate valve.
Item # BM-423
used 4 Cu.Ft. Marion Stainless Steel Ribbon Blender. 18" wide x 30" long trough. Double ribbon. Outboard roller bearings, air purge seals. 3 HP, 230/460 volt motor drive. Center bottom outlet with valve. S/N 00047. Built 2000
Item # BM-424
used 25 Cu.Ft. Oscar Krenz Stainless Steel Jacketed Ribbon Blender, Twin Shaft. 61" x 40" x 26.5" deep mixing chamber. 2-3" Outlets. Jacket rated 45 PSI @ 300 Deg.F.. Last used in sanitary food plant.
Item # BM-390
***SOLD*** used Munson Rotary Batch Blender. Model 701-TSS-50. Rated at 50 Cu.Ft. Batch volume and 105 Cu.Ft. total volume. Stainless Steel. Last used in sanitary food plant. Gear ratio 24.99:1 on gear box. Approx 7.5-10 HP Motor. (no nameplate on motor).
Item # BM-309
***SOLD*** used TriClover Tri-Blender. Model F3218MD-MBV. Has 4" Powder inlet, 1.5" Liquid inlet and 2" outlet. Has powder hopper. Mounted on stainless steel base with 15 HP, 230/460 volt, 1765 rpm motor. Last used in Food plant. Sanitary construction.
Item # BM-299
***SOLD*** Ross VMC-2 Triple Shaft (tri-shaft) Versamixer Mixer. 316 Stainless Steel construction. Vacuum capable. 2 gallon jacketed Vacuum capable mixing can with provision for thermal couple probe (Type J). 50 PSI jacket. Sanitary 80 grit finish. Explosion proof drives and controls. Anchor agitator driven by 1HP, 230/460 volt xp motor (2) high speed dispersers each driven by 1 HP, 230/460 volt motor. Air over bowl lift/lower mechanism. Lift System: 80-100psig/ 4-5 scfm. Electrical 115V/60Hz. Included are the the unit and electrical mounted on the unit. No main control panel included. Serial# 104930. High viscosity mixer.
Item # BM-353
Used Ross Model PVM-2, triple motion stainless steel mixer. 2 gallon. Stainless steel jacketed change can. Tri-Shaft Vacuum mixer. Triple mixers including (1) 1/2 hp 3 phase 60 cycel 208-230/460 volt 1725 rpm three wing anchor agitator with scrapers on side and bottom of can. (1) 3/4 hp 3 phase 60 cycle 208-230/460 volt 3450 rpm High Speed disperser. (1) 3/4 hp 3 phase 60 cycle 208- 230/460 volt 3450 rpm High shear rotor stator mixer. Mixer motors 30 Hp 3 phase 60 cycle 230/460 volt 1765 rpm. Change can is jacketed and on castors. Hydraulic lift. Includes Mokon heater Model DB41109BF 3 phase 60 cycle 460 volt 9 kw. Mounted all on mobile cart.
Item # BM-415
used 4 Gallon MYERS Triple Shaft Mixer/Disperser, Tri-shaft. Model HVL 550/500-7.5-991. Has (2) approx 4 gallon, 10.5" dia. x 12" deep, Jacketed, Vacuum rated mixing chambers. Has sweep blade, Disperser and paddle type agitation. Hydraulic lift. Mounted on Frame with wheels and has a Discharge press and spare mixing can.
Item # BM-257
used 2 Cu.Ft. Paterson Kelley Twin Shell Blender. Sanitary, Stainless Steel with Pharmaceutical grade finish. Rated 60 Lbs./Cu.Ft. material density. Unit has provisions for Liquid/Solids dispersion Bar. (No Bar installed) Shell has chain driven 3/4 HP, 208-220/440 volt with gear reducer for 25 RPM output. Bar drive is 2 HP with belts and guard. 6" Discharge with butterfly valve. 37" floor clearance. 14" charging ports with removable vented covers. Last use was pharmaceutical.
Item # BM-90
used Gemco 30 cu.ft. "V" twin shell blender. Stainless Steel. Rated 100 #/cu.ft. 5HP drive. Shell 13.6 rpm
Item # BM-252
8 Qt. used, Patterson Kelley Twin Shell, Liquid-Solids Blender. Stainless Steel. Unit has drive and provision for intensifier bar (bar not included). Bar drive is 3/4 HP, 3450 RPM, 115/230 v, 1 ph. Blender drive is 1/15 HP, 115 volt. Approx blender speed is 25 RPM. Laboratory blender, pilot scale blender.
Item # BM-313
used 300 Cu.Ft. Patterson Kelley Twin Shell "V" Blender. Stainless Steel. Rated 40 Lbs/Cu.Ft. Driven by 20 HP, 208-220/440 volt, 1770 rpm motor into gear reducer.
Item # BM-345
used 40 CU.FT. Patterson Kelley Twin Shell "V" Blender with Intensifier Bar. Stainless Steel. Rated 65 #/cu.ft. Min drive is 5 HP, 208 volt, 1740 rpm into Foote Bros gear reducer with 100 rpm output. Bar drive is 15 HP 200 volt, 1775 rpm. Included leg extensions. Last used in Food Plant.
Item # BM-398
used Patterson Kelley Yoke Style Blendmaster Laboratory Mixer. Twin Shell. Includes (2) Stainless Steel Shells. (1) Shell is 4" Dia. x 9" Lgth.(approx 2 Qt.). (1) Shell is 3.5" dia. x 7" lgth. (approx 1 Qt.) Laboratory blender, pilot scale blender.
Item # BM-400
used Gemco 16 Quart Twin Shell V Blender. Stainless Steel. S/N LB85662. Shells are 9" Dia. x 15" Lgth. 10" from center line to outlet. Laboratory blender, pilot scale blender.
Item # BM-401
used Gemco 4 Quart, (1/8th Cu.Ft.) Twin Shell V Blender. Stainless Steel. S/N LB-86705. Shells are 6" Dia. x 10" Lgth. 7" from center line to outlet. Laboratory blender, pilot scale blender.
Item # BM-407
8 Qt. used, Patterson Kelley Twin Shell, Liquid-Solids Blender. Stainless Steel. Unit has intensifier bar. PK# LB-10231. Bar drive is 1 HP, 3450 RPM, 115/230 v, 1 ph. Blender drive is 1/4 HP, 1725 rpm 115/230 volt. Rated 250 #/cu.ft. Laboratory blender, pilot scale blender.
Item # BM-408
8 Qt. used Patterson Kelley Twin Shell, Liquid-Solids Blender. Stainless Steel. PK# LB-863. Laboratory blender, pilot scale blender.
Item # BM-430
used 20 CU.FT. Twin Shell "V" Blender with Intensifier Bar. Stainless Steel. Has leg extensions. Last used in Food Plant. Believed to be a Patterson Kelley (PK Blender).
Item # BM-209
2400 Liter working capacity Fryma model VME 2400 vacuum mixer (~650 gallon), triple shaft, tri-shaft mixer. Fabrication # M10510. The tank has an overall height is 101" to top of lid including legs. It is 87" to the top with the lid removed. The overall diameter of tank with jacket is 63". The interior dimensions are 61" diameter with 54" straight side height, 11" dome top and 11" dish bottom. Working temperatures are 150 c for the interior and the jacket. The interior has a pressure rating of -1/+1 bar and the jacket has a 2.5 bar rating. There are two agitator drives, a 7.5 hp motor drives a center 3 prop agitator and a scrape agitator through a chain drive and a 50 hp motor drives a disperser type agitator off to the side of the center shaft. The top has an 8" flanged opening that is clamped shut and 6" glass inspection port with light. Top also has a 2" sanitary, 1.5" sanitary, and (2) 1" threaded fitting. The bottom has a 6" sanitary discharge with a pneumatically operated valve. Requires 230/ 460 vac 3 phase electrical supply. Previously used for toothpaste. Good Condition.
Item # BM-108
***SOLD***Used Fryma VME-120 Vacuum Processing Vessel, Sanitary construction, 200 liter (52.8 gallon) total, 50-120 liter (13-32 Gallon) working capacity, tri-shaft mixer, rated FV Internal,SS jacket rated 3 BAR, with 3 shaft (Tri-shaft) mixing: Consisting of(1)- anchor/sweep agitator w/scrapers driven by .75 KW motor, (1)- High speed agitator with dissolver/disperser blade has 4KW motor, (1) toothed colloid mill has 4KW motor. Vacuum Pump is: SIHI Model- LPHR-25007-ABAHF0A0. Direct driven by 2.2 KW, 3/60/220 Volt, 3400 RPM. Has bottom outlet. High viscosity mixer.
Item # BM-348
used 2400 liter Fryma VME-2400 Vacuum Processing Vessel, Dual Shaft, Sanitary construction, 2400 Liter (630 Gallon) working capacity. There are two agitator drives. A 7.5 hp motor drives a center 3 blade counter rotating agitator and a scrape agitator through a chain drive. A 50 hp motor drives a disperser type agitator off to the side of the center shaft. Working temperatures are 150 Deg.C (302 Deg.F.)for the interior and the jacket. The interior has a pressure rating of -1/+1 bar and the jacket has a 2.5 bar rating. The top has an 8" flanged opening that can be used for a colloid mill (not included) currently it is clamped shut and 6" glass inspection port with light. Top also has a 2" sanitary, 1.5" sanitary and (2) 1" threaded fitting. The bottom has a 6" sanitary discharge with a pneumatically operated valve. Requires 230/460 vac 3 ph electrical supply. Previously used for toothpaste. Tri-Shaft
Item # BM-349
Used Ross Model PVM300 dual motion stainless steel mixer. Mixing capacity 150 to 300 gallon. Full capacity 398 gallon. Stainless steel jacketed change can. Vacuum mixer. Dual mixers including (1) three wing anchor agitator with scrapers on side and bottom of can. (1) High Speed disperser Mixer motor 20 Hp 3 phase 50 cycle. Anchor Agitator motor 30 Hp. (with Foxboro Jordan 50/60 cycle converter). Change can is jacketed. Hydraulic lift.
Item # BM-350
Used Ross Model PVM300 Triple Motion Stainless Steel Mixer. Mixing capacity 150 to 300 gallon. Full capacity 398 gallon. Stainless steel jacketed change can 15 psi. Vacuum mixer. Triple mixers including (1) three wing anchor agitator with scrapers on side and bottom of can. (1) High Speed disperser. (1) High shear rotor stator mixer (requires head and cage). Mixer motors (1) 15 Hp and (2) 30 Hp 3 phase 60 cycle 230/460 volt 1765 rpm. Change can is jacketed and on castors. Hydraulic lift.
Item # BM-351
Used Ross Model PVM 40 dual motion stainless steel mixer. 40 gallon. S/N 4075. Stainless steel jacketed change can 50 psi. Vacuum mixer. Dual mixers including (1) three wing anchor agitator with scrapers on side and bottom of can and (1) High Speed disperser with vari-speed drive. Rear motor is 3 HP, 208-230/460, 1745 rpm and the main drive is 5 HP, 208-230/460 volt, 1760 rpm. Change can is on castors. Can serial number 11012-1B, National board number 415. Built 1994. Hydraulic lift.
Item # BM-352
Used Ross Model PVM 40 triple motion stainless steel Vacuum rated mixer. 40 gallon. Stainless steel jacketed change can 50 psi. Tri-Shaft Vacuum mixer. Triple mixers including (1) three wing anchor agitator with scrapers on side and bottom of can and (2) High Speed disperser (one shaft is carbon steel, all other shafts/blades stainless steel). Change can is on castors. Can serial number 11012-1A, National board number 414. Built 1994. Hydraulic lift.
Item # BM-354
***SOLD*** Used Hydraulic Discharge press for 40 Gallon Ross mixer cans, model DS40. Serial number 64824.
Item # BM-393
Used Brogli Multi Homo mixer. Stainless steel contacts. Model Multi Homo Type MH10C. 10 liter working capacity. .28 kw/.37 kw motor 3 phase 60 cycle 208 volt. Triple motion agitator. Anchor Hi/Lo Scraper. Spiral Agitators. Homogenizer. 3 phase 60 cycle 208 volt. 1600/3400 rpmTop mounted light. Mixer bowl rated 25 psi / Full vacuum @ 400 degrees F. Jacket rated 43.5 psi @ 400 degrees F. Serial Number WO2762. Built 1987. Bowl mounted on castors with manual lift. Vacuum pump inside control cabinet. Controls. Serial Number 2762. Pharmaceutical Mixer, internal polished.
Item # BM-413
Used 2 Gallon Premier Mill Dual Shaft Vacuum Mixer. Model ESD/V-2/1. Jacketd mix can. Has Scrape mixer and high shear Disperser. Drives are UL for Hazardous Locations (Explosion Proof) Drives are 2 HP, 230/460 volt, 3 ph, 5.2/2.6 amp, 1730 RPM and 1 HP 230/460 volt, 3 ph, 2.8/1.4 amp 1750 rpm. Both drive have vari-speed controllers and can be run together or independent. Last used in sanitary food plant.
Item # BM-74
Patterson Kelley 24" diameter Zig Zag Continuous Blender, size 24 CSN. Maximum density: 55 lbs/cu.ft., with 10 HP, 230/460 V, GE Motor and gear chain drive. Believed to be Unused.